The Titanium 45a Plasma Cutter In 2022: Recommendations & Advice
By, Adam AlterUpdated
After a long time searching and testing, we, today, want to provide you with from 4,182 reviews of our former customers. Moreover, we rank 12 Titanium 45a plasma cutter you may be fond of in 2022. Simultaneously, you are expected to go through some most famous manufacturers worldwide, such as N.h, Reboot, Herocut, Zs- mictek, Lotos, Tooliom, Warfox, Hynade, S7, Primeweld, Yeswelder.
Our Top Picks
- ✤Dual Voltage 110/220V, Voltage auto change. Max current is 35Amps under 110V clean cutting thickness 8mm @65PSI 35A 110V. Max 45Amps under 220V, Max cutting thickness [email protected] 40A 220V 45A
- ✤LED Current Display, 110/220V power lamp, Current knob, Time for post air can be adjust. Duty cycle 60% in 45A, 100% in 35Amps, Maybe the cutting arc not stable if the air less or over the range. We suggest air pressure 65PSI (0.6Mpa).
- ★Cutting Ability:Plazma cutter Automatic 110/220v ac-dc dual voltage,10-50A dc output, 1/2''(12mm) ideal clean cut and 3/5''(15mm) maximum severance cut on 220v;10-40A dc output, 1/3"(8mm) ideal clean cut and 2/5"(10mm) maximum severance cut on 110v.
- ★Attentive Suport Service:We have over 10 years professional production experience of plasma cutter, buy this plasma cutter with confidence as offers 1 year limited warranty and free consumables guarantee,besides,you will get a local supports for any assistance.
- [Generator Supported] this plasma cutter 45amp works well with a generator,but we suggest a 5000W above generator and 30A breaker needed for 220V
- [Warranty] buy this plasma cutter with confidence as Reboot offers 1-year limited warranty and free consumables guarantee,besides,you will get a local supports for any assistance
- Max Cut Thickness: 1/2"
- The compactible consumables set, for this Brown Color LTPDC2000D Plasma Cutter are "PCS22" or "PCS33". Please search "Lotos PCS22" or "Lotos PCS33". It CANNOT compatible with Lotos PCON40 or PCON90 Consumables Sets or any other third part consumables set
- ★INPUT: Automatic Dual Voltage 110~125V or 215~245V. Fully Output Circuit Breaker Requiement: 110V @ 50A and 220V @ 40A. Air Compressor Requirement: 70 PSI @ 4.0SCFM. ★OUTPUT: 20-55 A DC output, 3/5” ideal clean cut and 1” maximum severance cut under 220/240V. 20-35A DC output, 3/8" ideal clean cut and 1/2" maximum severance cut under 110/120V. ★SUITABLE CUTTING--for Stainless Steel, Alloy Steel, Mild Steel, Copper, Aluminum, etc. Uses non-hazardous compressed air to cut, safe and at low cost.
- ★ BUY WITH CONFIDENCE: We offer 30 days refund and a 3-YEARS Limited Warranty: include 1 Year NEW Replacement Warranty. ★ US BASED CUSTOMER CARE & SUPPORT TEAM: please feel free to contact us by phone or email, we always stand Back on Our Products. Please submit the registration form on our website.
- Non-touch Polit ARC: Can effectively cut rough, painted and rusty surfaces, and generates the least slag. The torch head does not need to touch the metal plate, then it will start arc. Better cutting quality and longer consumable life
- Portable: Auto-voltage adapts to 110 V - 220 V input power with adapter. Lightweight 13lb, can be carry and storage anywhere you need.
- 🛒Plasma Cutter Max rated clean cutting thickness: 9mm. 【50A breaker suggested for 110V】
- 🛒Cutting Material: aluminum,stainless steel, alloy steel, mild steel, copper, cast iron and chrome.
- Max cutting thickness 14mm ,10mm quality cutting thickness in [email protected] 50A; Under 120V, it is 35Amps.Quality cutting thickness is 8mm, Severance cutting thickness is 12mm
- Accessories included:4M PT31 cutting torch, 2.5M Earth clamp,5pcs tips, 5pcs electrodes, 2 meters air hose, 4pcs hose clamp, 1adaptor, 1 manual.Air regulator,air filter,air gauge are fixed at machine
- ★ THE COMPATIBLE CONSUMABLES SETS for this BROWN Color LT5000D Plasma Cutter are "LCS22" or "LCS33". Please search "Lotos LCS22" or "Lotos LCS33"; ★ It CANNOT compatible with Lotos LCOn20, LCON40 or LCON90 Consumables Sets or any other third part consumables set. ★ PACKAGE INCLUDES: Power supply, Plasma cutting torch, ground clamp, Pre-installed NPT 1/4” industry type D plug and Air filter regulator, consumables, Instruction Manual, etc.
- ★ AIR PLASMA CUTTER: SUITABLE CUTTING for Stainless Steel, Alloy Steel, Mild Steel, Copper, Aluminum, etc. ★ SAFE AND AT LOW COST: compact plasma cutter has a handle for portability and uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper, and aluminum.
Compare Specs Titanium 45a plasma cutter
| Our Picks | Our Score | Brand | Color | Size (In.) | Weight (lb) | Delivery | |
|---|---|---|---|---|---|---|---|
|
Theia Plasma Tips&Electrode 30pcs 56811 56255 45Amp (30)
|
Check Price | N.H | - | 0.4 x 3.9 x 5.1 | - | - | |
Plasma Cutter 50 Amp 1/2" Clean Cut CUT50D 110V/220V IGBT Air Plasma Cutting Machine Compact Metal Cutter High Frequency Inverter Cutting for Alloy Mild Steel Cast Iron and Chrome
|
Check Price | Reboot | GREEN | 9.8 x 11.0 x 14.5 | 19.80 |
prime
|
|
Reboot Plasma Cutter Machine 220V 3/5'' MAX Cutting IGBT Inverter Air Plasma Cutting 1/2" Clean Cut High Frequency Duty Cycle for Aluminum Stainless Mild Steel Copper Iron Chrome
|
Check Price | Reboot | GREEN | - | - |
prime
|
|
Herocut Plasma Cutter, 45Amp Plasma Cutting Machine, Dual Voltage 110V/220V
|
Check Price | HEROCUT | - | - | - |
prime
|
|
Plasma Cutters 45Amp 110/220V Plasma Cutting Machine,1/2'' Clean Cut High Frequency IGBT Portable Plasma Cutter for Car Frame,Carbon Steel,Stainless Steel,Thin Copper,Aluminum
|
Check Price | ZS- MICTEK | orange+black | - | 9.60 |
prime
|
|
Reboot Plasma Cutter
|
Check Price | Reboot | Green | - | - |
prime
|
|
LOTOS LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter, Dual Voltage 110V/220V
|
Check Price | LOTOS | Brown | 6.0 x 12.0 x 15.0 | 19.40 |
prime
|
|
Lotos Supreme LTP5500D Non-Touch Pilot Arc Plasma Cutter, Dual Voltage 110V/220V
|
Check Price | LOTOS | - | 7.1 x 12.0 x 16.0 | - |
prime
|
|
TOOLIOM 50A Non-Touch Pilot ARC Air Plasma Cutter Dual Voltage 110V/220V IGBT Inverter Metal Cutting Machine 1/2" Clean Cut
|
Check Price | TOOLIOM | - | - | - |
prime
|
|
Reboot Plasma Cutter Machine Inverter RBC-4000 AC 110V Air 1/2'' Plasma Cutting High Frequency 90% Duty Cycle for Aluminum Stainless Mild Steel Copper Iron Chrome
|
Check Price | Reboot | Green | - | - |
prime
|
|
Warfox Plasma Cutter 120/240V Dual Voltage Plasma Cutting Machine
|
Check Price | warfox | - | - | 8.20 |
prime
|
|
Lotos LT5000D Plasma Cutter 50Amps Dual Voltage Compact Metal Cutter 110/220V AC 1/2" Clean Cut
|
Check Price | LOTOS | - | 13.0 x 26.0 x 10.0 | 22.50 |
prime
|
|
hynade Plasma Cutter, Dual Voltage 115/230V plasma cutting machine
|
Check Price | hynade | - | - | - |
prime
|
|
50Amp Non-Touch Pilot Air Plasma Cutter 110V
|
Check Price | S7 | Blue | - | - |
prime
|
|
PRIMEWELD CUT60 60Amp Non-Touch Pilot Arc PT60 Torch Plasma Cutter 110V/220V Dual Voltage 3 Year Warranty
|
Check Price | PRIMEWELD | - | 11.0 x 19.0 x 20.0 | - | - | |
YESWELDER CUT-55DS 55Amp Non-Touch Pilot Arc Air Plasma Cutter 1/2 Inch Clean Cut
|
Check Price | YESWELDER | - | - | - |
prime
|
What Are the Most Critical Aspects of Titanium 45a plasma cutter That You Should Concentrate on?
You must know the Titanium 45a plasma cutter to make a substantial purchase. There's a slew of additional issues which have to be looked at and assessed. Each commodity has its own set of difficulties. As a result, you can rely on us to give you comprehensive counsel and support.
Through AI and Big Data, this post offers properly reviewed and selected product information. The goal is to provide you with a reliable and accurate set of data.
You might quickly become overwhelmed on your quest for the Titanium 45a plasma cutter because there are so many models and features. Avoid being suffocated by an expensive item that only serves to take up room in your cupboard by following our advice.
Pilot Arc
Plasma cutters with better cutting features will include a pilotarc. This allows you to make cuts without your torch tip coming in contact with any metal. The pilot arc can be used to cut through rusty and painted surfaces. If you plan to cut rusty, or painted surfaces, you will need to wash the spot where the ground clamp is connected. If you are working on metal that has gaps, such as mesh sheets, it is not necessary to stop or start the torch. The continuous arc will keep the torch lit. A pilot arc is a standard feature for most welders, except those made in China.
Ideal Cut
When choosing a plasma cutter, the first thing to consider is how thick it can cut metal. Consider the thickness of the metal that you will be using most often and search for an optimal cut at this thickness. The machine is capable of cutting mild metal at 10 inches per hour. You won't get as much out of the severance cutter. It will produce less quality results. The ideal cut is the best choice if you want quality cuts.
Severance Thickness
To cut metal effectively, the plasma cutter must be able to cut up to a severance thickness. The severance thickness will result in a slow cut and the machine not producing enough heat to make a clean-cut. For regular or best results, it is not recommended to cut metal at the thickness of the severance.
Duty Cycle
The machine's duty cycle is the time it can continue to operate without cooling down. A 35% duty cycle with a fixed amperage and voltage would mean the plasma cutter could run for approximately 3.5 minutes, instead of 10, without needing to cool down. Lower amperage will result in a longer duty cycle. For deep, long-lasting metal cutting, a longer duty cycle with a greater amperage will be more efficient.
Voltage
The plasma cutters can be used with an indoor power supply that is compatible with 110/115/120V input power. They are ideal for home use or beginners, however they have a limited power output. You will need a plasma cutter with a 220V input if you require more power. This is not compatible with generators. You can choose between two power supply options for your plasma cutter: 110V or 220V. These are my favorites because of their versatility.
Built-in Air Compressor
You will need to add an air compressor to most plasma cutters before it can be used. Some plasma cutters have an integrated air compressor. They are more costly but offer more convenience as you don't have to bring your own compressor if you go out into the field. It doesn't require you to connect an air compressor or any other equipment. You can just plug the device in and get cutting. They are worth looking into for a little extra cash.
Safety
Safety should be your top priority. You should read all safety information provided by the plasma cutter. To protect your eyes, make sure to get good safety glasses. Although the arc may not be as strong as welding, it could still cause damage to your eyes. You can try shades 3 and 5 glasses. Avoid synthetic gloves as they may melt or stick to skin. Always use leather gloves. To protect your skin from the sparks and arc, cover your arms, legs and body with durable cotton material. To prevent injuries from metal falling, you should wear steel protection boots while you are chopping.
Weight
When buying equipment, weight is an important consideration. You don't want your equipment to weigh you down. Inverter technology has made most plasma cutters relatively lightweight. A plasma cutter that has an integrated air compressor might weigh a little more, but it will be much easier to transport as all you need is the plasma cutter.
Consumables
Consumables will cost you an ongoing fee after your plasma cutter is purchased. Consumables include the shield cap, nozzle and shield caps, as well as the swirl ring. Each one has a different life expectancy depending on many variables. However, they will all be damaged when the torch is used to pierce metal or the molten metal returns onto it. Otherwise, the hole must be perfect round. The put depth will affect how the cut is made. Long-lasting consumables are more common for more costly welders. Because of the high quality consumables, Hypertherm machines can be expensive but have low operating costs.
FAQs
1. Is A Cheap Plasma Cutter Worth It?
You should not buy a low-quality plasma cutter. It will not deliver the power, durability and quality you need. A plasma cutter with low prices may be able to cut thinner sheets.
2. Can We Cut Wood Or Plastic With A Plasma Cutter?
It is impossible to cut nonconductive materials. Plastic and wood are both electrically resistant materials.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
3. How Do You Set Up A Plasma Cutter?
Plasma cutting works on the principle that complete electric current is used. Therefore, a ground clamp will be required. You should choose a safe surface for your workshop that allows you to move freely around the work area.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
4. How Do I Choose A Plasma Cutter?
Consider the cost of the plasma cutter and the inputs. Will they provide enough power to cut through the desired thickness?
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
5. What Is Possible To Cut By Plasma Cutting?
Plasma cutting can be done with all electrically conductive metals, as long as there is an electric current circuit running through the workpiece and clamp.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
6. How Much Air Pressure Is Needed For A Plasma Cutter?
It is best to buy a compressor with 1.5x the CFM (cubic feet per hour) that the plasma cutter requires. Then, have it delivered at the PSI (pounds/square inch) that the tool needs.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
7. Why Does My Plasma Cutter Cut On An Angle?
Plasma metal cutters can plasma cut at odd angles for a variety of reasons. These include the following: The torch nozzle is worn; there's insufficient power to thearc; you are cutting too fast for your power rating; there's too much gas going to thenozzle; or the plasma cutter is working too slowly.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
8. How Much Faster Is A Plasma Cutter?
Plasma cutting is the best method of cutting metal. A good plasma cutter can cut up to 200 inches of metal per minute.
People are still working to increase the speed. Better speed means better products.
People are still working to increase the speed. Better speed means better products.
After all, it's time for you to pick up your buddy based on the things above. Don't waste your time at any unreliable site. As mentioned above, our website includes not only interesting information but authoritative one, so that you should come to us as regularly as possible.
We always welcome your feedback, whether positive or negative, since all of them will contribute to improving our site. Please join us for better service and wish you a cherishing shopping!
By, Adam Alter
