Plasmargon Plasma Cutter: Top Picks 2022
By, Bruce SchneierUpdated
We have a group of professionals in the market research field. They all join hands to survey of Plasmargon plasma cutter in 2022. According to nearly 2,241 reviews from former users, we pick 12 models from well-known brands like Plasmargon, S7, Lotos, Primeweld, Hynade, Herocut, Dynaloop, Tooliom, Warfox so that you can minimize the product scale more straightforward.
Our Top Picks
- 🛡️ Non-Touch Pilot Arc Plasma Cutter★: Pilot Arc Technology Allows You To Cut Without Touching The Tip To The Metal.Efficiently Cuts Though Rough, Painted, And Rusty Surfaces. Portablet Plasma Cutter Has A Handle For Portability And Uses Non-hazardous Compressed Air To Cut Stainless Steel, Alloy Steel, Mild Steel, Copper, And Torch Efficiently Cuts Though Rough, Painted, And Rusty Surfaces And Produces Minimal Slag; Better Cutting Quality And Longer Consumable Life
- 🛡️Plasma Cutter Can Be Plugged Into 120V / 230V Dual Voltage Using(Automatic Fitting)
- Output and performance: 10-50 A DC output, 1/2” ideal clean cut and 3/4” maximum severance cut under 220/240V. 10-35A DC output, 1/3" ideal clean cut and 2/5" maximum severance cut under 110/120V. SUITABLE CUTTING for Stainless Steel, Alloy Steel, Mild Steel, Copper, Aluminum, etc. Uses non-hazardous compressed air to cut, safe and at low cost.
- 50 Amp Digital Inverter Air Plasma Cutter
- PT60 blowback cutting torch WITH EURO CENTRAL CONNECTION
- Continuous Pilot Arc enables you to cut expanded, rusted, painted metals
- 👉 Post Time Function, Machine with function post time 2-15seconds, Adjust the time for the air keep blowing out from the torch head, Cooling torch and consumables, Warranty: two years for this plasma cutting machine. Free service in American if machine getting any problem within two years (not include accessories, they are consumables)
- 👉 This is 50Amps plasma cutter, CUT50H 110/220V dual voltage plasma cutting machine, It is air inverter technology 50/60Hz, severance max cutting thickness is 14mm, quality cutting thickness is 10mm, this plasma cutter is high frequency need to touch metal get arc starting.
- ✌ hynade is high level brand at welding field. We focus on welding business more than 20 years. Also we have a service team in American.
- ✌ Input voltage is 115/230v, Max current is 35Amps under 115V clean cutting thickness 4mm @65PSI 35A 115V. Max 40Amps under 230V, Clean cutting thickness [email protected] 40A 230V 45A up Power breaker is suggested.
- ★ OUTPUT & PERFORMANCE: 10-50 Amp DC output, 1/2” ideal clean cut and 3/4” maximum severance cut under 220/240V. 10-35A DC output, 1/3" ideal clean cut and 2/5" maximum severance cut under 110/120V. Engine Power : Electric (AC)★ DUAL VOLTAGE INPUT: Automatic Dual Voltage / Dual Frequency (110/120 V 220/240 V 50/60Hz).
- ★ THE COMPATIBLE CONSUMABLES SETS for this BROWN Color LT5000D Plasma Cutter are "LCS22" or "LCS33". Please search "Lotos LCS22" or "Lotos LCS33"; ★ It CANNOT compatible with Lotos LCOn20, LCON40 or LCON90 Consumables Sets or any other third part consumables set. ★ PACKAGE INCLUDES: Power supply, Plasma cutting torch, ground clamp, Pre-installed NPT 1/4” industry type D plug and Air filter regulator, consumables, Instruction Manual, etc.
- ✤ Very good to cut car flame, Clean cutting thickness 6mm Max cutting thickness 8mm in 110V 60PSI Machine only work in 110V not 220V, Please confirm the voltage before buying this machine. Machine maybe explode if connect it to 220V, Be careful~!
- ✤ Plasma Cutter, 110V 35A cutting machine with IGBT inverter technology, It is long life and efficient higher than mosfet machine.
- 【Dual Voltage 110/220V】：This plasma cutter designed under 110/220V, auto inspect indicate 110 and 220v, hand switch is not required on machine. There are two voltage lights at front of panel, 110V lighting when connect machine to power 110V, light 220V will lighting up when connect machine to power 220V, In this case the user easy knows the what kinds of voltage connecting machine.
- 【Cutting Thickness】：This plasma cutter easy cut all metals especially stainless steel. Quality cutting thickness for steel is 10mm#65PSI(0.65Mpa) 220V 50Amps, Max cutting thickness 14mm#65PSI 220V 50Amps; Under 110V 35Amps, the quality cutting thickness is 6mm#60PSI(0.6Mpa) 110V Max cutting thickness is 10mm#60PSI(0.6Mpa) 110V. The current for this plasma cutting machine, 50Amps in 220V, 35Amps in 110V. To cut copper, 3mm#60PSI(0.6Mps)220V 50Amps is suggested.
- Safety Protection: Certificated by ETL, built in over current protection, over load protection, temperature control.
- Portable: Auto-voltage adapts to 110 V - 220 V input power with adapter. Lightweight 13lb, can be carry and storage anywhere you need.
Compare Specs Plasmargon plasma cutter
| Our Picks | Our Score | Brand | Color | Size (In.) | Weight (lb) | Delivery | |
|---|---|---|---|---|---|---|---|
|
PLASMARGON 520TSC Plasma Cutter 200A TIG MMA Welder 50A Plasma Cutter
|
Check Price | PLASMARGON | Blue | 11.8 x 9.8 x 15.7 | - |
prime
|
|
PLASMARGON Plasma Cutter 4 in 1 Welders 520TSC DC Inverter TIG MMA CUT Pulse 50A 110/220V,Tungsten Rod Argon Arc Welding Machine
|
Check Price | PLASMARGON | - | - | - | - | |
PLASMARGON Air Plasma Cutter WSD60 SG55 Pilot Arc Torch Plasma Cutting Tools 10ft 16ft 23ft (16ft)
|
Check Price | PLASMARGON | - | - | - | - | |
50Amp Non-Touch Pilot Air Plasma Cutter 110V
|
Check Price | S7 | Blue | - | - |
prime
|
|
LOTOS LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter, Dual Voltage 110V/220V
|
Check Price | LOTOS | Brown | 6.0 x 12.0 x 15.0 | 19.40 |
prime
|
|
PRIMEWELD CUT60 60Amp Non-Touch Pilot Arc PT60 Torch Plasma Cutter 110V/220V Dual Voltage 3 Year Warranty
|
Check Price | PRIMEWELD | - | 11.0 x 19.0 x 20.0 | - | - | |
Plasma Cutter, CUT50H 50A Dual Voltage 110/220V, AG60 Torch Plasma cutting machine
|
Check Price | hynade | - | - | - |
prime
|
|
hynade Plasma Cutter, Dual Voltage 115/230V plasma cutting machine
|
Check Price | hynade | - | - | - |
prime
|
|
Lotos LT5000D Plasma Cutter 50Amps Dual Voltage Compact Metal Cutter 110/220V AC 1/2" Clean Cut
|
Check Price | LOTOS | - | 13.0 x 26.0 x 10.0 | 22.50 |
prime
|
|
Herocut Plasma Cutter, 35Amp Plasma Cutting Machine
|
Check Price | HEROCUT | - | - | - |
prime
|
|
Dynaloop 50A Pilot Arc Plasma Cutter
|
Check Price | Dynaloop | - | - | - |
prime
|
|
TOOLIOM 50A Non-Touch Pilot ARC Air Plasma Cutter Dual Voltage 110V/220V IGBT Inverter Metal Cutting Machine 1/2" Clean Cut
|
Check Price | TOOLIOM | - | - | - |
prime
|
|
PrimeWeld 3-in-1 50 Amp Plasma Cutter
|
Check Price | PRIMEWELD | - | - | - | - | |
Warfox Plasma Cutter 120/240V Dual Voltage Plasma Cutting Machine
|
Check Price | warfox | - | - | 8.20 |
prime
|
For a Practical Purchase of Plasmargon plasma cutter, What Should You Think About?
Actually, when you decide to invest in Plasmargon plasma cutter for yourself, lots of things to consider! It's harder to choose since the product comes with many types, functions, and features from different manufacturers. That’s why you should find a reliable space to acquire knowledge related to the item.
You are supposed to rest assured because we are here to support you with that. Our article here is conducted with the support of high-tech tools, including AI tools and Big Data. As a result, the authority and precision of the information are substantial.
We’ve highlighted the essential features of the Plasmargon plasma cutter below. Along with checking out the list of best models in the list, you should also carefully read the buying guide here:
Pilot Arc
Plasma cutters with better cutting features will include a pilotarc. This allows you to make cuts without your torch tip coming in contact with any metal. The pilot arc can be used to cut through rusty and painted surfaces. If you plan to cut rusty, or painted surfaces, you will need to wash the spot where the ground clamp is connected. If you are working on metal that has gaps, such as mesh sheets, it is not necessary to stop or start the torch. The continuous arc will keep the torch lit. A pilot arc is a standard feature for most welders, except those made in China.
Severance Thickness
To cut metal effectively, the plasma cutter must be able to cut up to a severance thickness. The severance thickness will result in a slow cut and the machine not producing enough heat to make a clean-cut. For regular or best results, it is not recommended to cut metal at the thickness of the severance.
Weight
When buying equipment, weight is an important consideration. You don't want your equipment to weigh you down. Inverter technology has made most plasma cutters relatively lightweight. A plasma cutter that has an integrated air compressor might weigh a little more, but it will be much easier to transport as all you need is the plasma cutter.
Built-in Air Compressor
You will need to add an air compressor to most plasma cutters before it can be used. Some plasma cutters have an integrated air compressor. They are more costly but offer more convenience as you don't have to bring your own compressor if you go out into the field. It doesn't require you to connect an air compressor or any other equipment. You can just plug the device in and get cutting. They are worth looking into for a little extra cash.
Duty Cycle
The machine's duty cycle is the time it can continue to operate without cooling down. A 35% duty cycle with a fixed amperage and voltage would mean the plasma cutter could run for approximately 3.5 minutes, instead of 10, without needing to cool down. Lower amperage will result in a longer duty cycle. For deep, long-lasting metal cutting, a longer duty cycle with a greater amperage will be more efficient.
Safety
Safety should be your top priority. You should read all safety information provided by the plasma cutter. To protect your eyes, make sure to get good safety glasses. Although the arc may not be as strong as welding, it could still cause damage to your eyes. You can try shades 3 and 5 glasses. Avoid synthetic gloves as they may melt or stick to skin. Always use leather gloves. To protect your skin from the sparks and arc, cover your arms, legs and body with durable cotton material. To prevent injuries from metal falling, you should wear steel protection boots while you are chopping.
Consumables
Consumables will cost you an ongoing fee after your plasma cutter is purchased. Consumables include the shield cap, nozzle and shield caps, as well as the swirl ring. Each one has a different life expectancy depending on many variables. However, they will all be damaged when the torch is used to pierce metal or the molten metal returns onto it. Otherwise, the hole must be perfect round. The put depth will affect how the cut is made. Long-lasting consumables are more common for more costly welders. Because of the high quality consumables, Hypertherm machines can be expensive but have low operating costs.
Ideal Cut
When choosing a plasma cutter, the first thing to consider is how thick it can cut metal. Consider the thickness of the metal that you will be using most often and search for an optimal cut at this thickness. The machine is capable of cutting mild metal at 10 inches per hour. You won't get as much out of the severance cutter. It will produce less quality results. The ideal cut is the best choice if you want quality cuts.
Voltage
The plasma cutters can be used with an indoor power supply that is compatible with 110/115/120V input power. They are ideal for home use or beginners, however they have a limited power output. You will need a plasma cutter with a 220V input if you require more power. This is not compatible with generators. You can choose between two power supply options for your plasma cutter: 110V or 220V. These are my favorites because of their versatility.
FAQs
1. Why Does My Plasma Cutter Cut On An Angle?
Plasma metal cutters can plasma cut at odd angles for a variety of reasons. These include the following: The torch nozzle is worn; there's insufficient power to thearc; you are cutting too fast for your power rating; there's too much gas going to thenozzle; or the plasma cutter is working too slowly.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
2. How Do You Set Up A Plasma Cutter?
Plasma cutting works on the principle that complete electric current is used. Therefore, a ground clamp will be required. You should choose a safe surface for your workshop that allows you to move freely around the work area.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
3. Can We Cut Wood Or Plastic With A Plasma Cutter?
It is impossible to cut nonconductive materials. Plastic and wood are both electrically resistant materials.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
4. Is A Cheap Plasma Cutter Worth It?
You should not buy a low-quality plasma cutter. It will not deliver the power, durability and quality you need. A plasma cutter with low prices may be able to cut thinner sheets.
5. How Do I Choose A Plasma Cutter?
Consider the cost of the plasma cutter and the inputs. Will they provide enough power to cut through the desired thickness?
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
6. What Is Possible To Cut By Plasma Cutting?
Plasma cutting can be done with all electrically conductive metals, as long as there is an electric current circuit running through the workpiece and clamp.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
7. How Much Faster Is A Plasma Cutter?
Plasma cutting is the best method of cutting metal. A good plasma cutter can cut up to 200 inches of metal per minute.
People are still working to increase the speed. Better speed means better products.
People are still working to increase the speed. Better speed means better products.
8. How Much Air Pressure Is Needed For A Plasma Cutter?
It is best to buy a compressor with 1.5x the CFM (cubic feet per hour) that the plasma cutter requires. Then, have it delivered at the PSI (pounds/square inch) that the tool needs.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
After knowing the suitable kinds of Plasmargon plasma cutter and the features you wish, it’s high time for you to start your shopping. Note that you shouldn’t run out to a particular store or start scrolling through online sales just yet. With the development of technology, especially the expansion of sale sites, you can easily find your buddy.
Remember to check out our site weekly round-up to ensure that the current sales on Plasmargon plasma cutter perform well in our tests. So you can catch up with them as soon as possible. Would you please give us your feedback for better service? Many thanks!
By, Bruce Schneier
