Plasma Cutter Jegs Of 2022: Guidances, Suggestions, And FAQs
By, Adam AlterUpdated
Our specialists conducted a Plasma cutter jegs in 2022 test. This test aims to collect data on 6,848 evaluations from consumers who are interested in and can invest in the items. Read on to learn about the best 12 models from well-known suppliers like Jegs, Tooliom, Liaohsuan, Super deal, Lotos, Hynade, S7, Display4top, Mophorn, Herocut, Warfox.
Our Top Picks
TOP Choice #3
![Welding Cart, Welding Carts for MIG/TIG Welder and Plasma Cutter, Black]()
- 【Wide range of applications】Suitable for a wide range of applications including sheet metal fabrication, light industrial use, site work, automotive, ducting work, repair and maintenance services. The cutting machine not only use in businesses and DIY users but also fully accommodating the demands of professional operators.
- 【Considerable & Safe design】Built-in over-heat protection, over-voltage protection, under voltage protection and over heat protection. Comes with wire and mask, which can prevent you from hurting while using.
- Max Severance Thickness: 3/4"
- PAPST Advanced German Cooling System
- 👉 Post Time Function, Machine with function post time 2-15seconds, Adjust the time for the air keep blowing out from the torch head, Cooling torch and consumables, Warranty: two years for this plasma cutting machine. Free service in American if machine getting any problem within two years (not include accessories, they are consumables)
- 👉 Cutting Thickness, this plasma cutter easy cut all metals especially stainless steel. Quality cutting thickness for steel is 10mm#70PSI(0.65Mpa) 220V 50Amps, Max cutting thickness 14mm#70PSI 220V 50Amps; Under 110V 35Amps, the quality cutting thickness is 6mm#65PSI(0.6Mpa) 110V Max cutting thickness is 10mm#60PSI(0.6Mpa) 110V. The current for plasma cutting machine, 50Amps in 220V, 35Amps in 110V. for cut copper, 2-4mm#60PSI(0.6Mps)220V 50Amps is suggested.
- 🛡️50 Amp OUTPUT ★: Up To 50A Output Current Can Cut Up To 31/64 Inch (13.0mm) Plate. Equipped With Digital Display And Alarm LED, Read The Output Welding Current
- 🛡️Plasma Cutter Can Be Plugged Into 120V / 230V Dual Voltage Using(Automatic Fitting)
- ★High Efficiency and Energy Saving:The plasma cutter machine by using inverter technical of switch power,more stable performance. High duty cycle result in less power consumption. More economical and effcient than the traditional cutting machine due to the high speed, high temperature and high energy plasma draught.
- ★ Specification：Voltage: 110/220V, 60HZ, 4.8KVA; Main Fuse: 16/22A; Current rage:20-50A; No-load Voltage:230V; Duty cycle: 60%; Efficiency:85%; Insulation class:F; Protection class: IP21S; Max cutting thickness:1-12mm.
- 14MM Cutting Thickness: Support 1-14mm thickness metal cutting. Faster cutting speed, low noise and smooth cut surface.
- Wide Applications: Suitable to cut most metals, like: stainless steel, alloy, aluminum, mild steel, carbon steel etc. Can be widely used at automotive, ducting work, repair & maintenance, metal processing, manufacture, site work etc.
- ★ AIR PLASMA CUTTER: SUITABLE CUTTING for Stainless Steel, Alloy Steel, Mild Steel, Copper, Aluminum, etc. ★ SAFE AND AT LOW COST: compact plasma cutter has a handle for portability and uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper, and aluminum.
- ★ SETUP WITHIN 1 MIN: The pre-installed NPT 1/4” industry type D plug and air filter regulator allows you to quick connect to your air compressor by using the stand coupler existing on your air compressor. The whole machine can be setup quickly within 1 min.
- 👍 The plasma cutter easy to cut stainless steel, Alloy steel, mild steel, Copper etc. Quality cutting torch PT31 come with machine, Max cutting thickness is 10mm at 40Amps 220V 60PSI.
- 👍 Machine come with 220V power plug, We provide one year warranty for this unit.
- The cutting machine can cut carbon steel, stainless steel, steel and other materials. It is an indispensable machine in your tool room
- Accessories included:4M PT31 cutting torch, 2.5M Earth clamp,5pcs tips, 5pcs electrodes, 2 meters air hose, 4pcs hose clamp, 1adaptor, 1 manual.Air regulator,air filter,air gauge are fixed at machine
Compare Specs Plasma cutter jegs
| Our Picks | Our Score | Brand | Color | Size (In.) | Weight (lb) | Delivery | |
|---|---|---|---|---|---|---|---|
|
JEGS Plasma Cutter | 110V AC | 220V AC | 60% @ 30A | Cuts Steel And Iron Up To 3/8 “ Thick
|
Check Price | JEGS | - | 20.3 x 15.1 x 10.5 | - | - | |
TOOLIOM 50A Non-Touch Pilot ARC Air Plasma Cutter Dual Voltage 110V/220V IGBT Inverter Metal Cutting Machine 1/2" Clean Cut
|
Check Price | TOOLIOM | - | - | - |
prime
|
|
|
Welding Cart, Welding Carts for MIG/TIG Welder and Plasma Cutter, Black
|
Check Price | LIAOHSUAN | Black | 14.6 x 28.0 x 33.5 | - |
prime
|
|
SUPER DEAL DC Inverter Plasma Cutter Cutting Machine With Screen Display Dual Voltage 110/220V AC 1/2'' Clean Cut (CUT 50)
|
Check Price | SUPER DEAL | Orange | 11.8 x 5.9 x 15.1 | 24.40 | - | |
LOTOS LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter, Dual Voltage 110V/220V
|
Check Price | LOTOS | Brown | 6.0 x 12.0 x 15.0 | 19.40 |
prime
|
|
Plasma Cutter, CUT50H 50A Dual Voltage 110/220V, AG60 Torch Plasma cutting machine
|
Check Price | hynade | - | - | - |
prime
|
|
50Amp Non-Touch Pilot Air Plasma Cutter 110V
|
Check Price | S7 | Blue | - | - |
prime
|
|
Display4top CUT-50 DC Inverter Plasma Cutter,110/220V Dual Voltage Compact Metal Cutting Machine
|
Check Price | display4top | - | - | - |
prime
|
|
Mophorn 50Amp Non-Touch Pilot Arc Plasma Cutter
|
Check Price | Mophorn | 50 Amp 110/220v Pilot Arc | 5.9 x 9.1 x 14.9 | 11.48 | - | |
Lotos LT5000D Plasma Cutter 50Amps Dual Voltage Compact Metal Cutter 110/220V AC 1/2" Clean Cut
|
Check Price | LOTOS | - | 13.0 x 26.0 x 10.0 | 22.50 |
prime
|
|
Herocut Plasma Cutter, 45Amp Plasma Cutting Machine
|
Check Price | HEROCUT | - | - | - |
prime
|
|
Warfox Plasma Cutter 120/240V Dual Voltage Plasma Cutting Machine
|
Check Price | warfox | - | - | 8.20 |
prime
|
How Would You Realize Whether Plasma cutter jegs Fulfill Your High Standards?
When selecting a suitable Plasma cutter jegs, a variety of factors have been found. Information sources are available in a wide range of forms. As a basis, we are doing it to support, inform, and solve your demands.
The decider will feature some of the essential items on the market and address some of the most common questions:
- What factors should you examine when determining the best matches your demands?
- Where is the reliable place to send the request?
- Where should you start to ask for support for the impact lines of this product?
- What are the benefits of purchasing the item?
- Why does it matter whether the product is suitable?
Cos of the widespread utilization of sales websites and forums, Plasma cutter jegs are still one of the most relevant and essential sources of information available on the Internet today.
Both people and technology were created and appraised. A more in-depth evaluation of these aspects would be beneficial. Keep these things in mind.
Ideal Cut
When choosing a plasma cutter, the first thing to consider is how thick it can cut metal. Consider the thickness of the metal that you will be using most often and search for an optimal cut at this thickness. The machine is capable of cutting mild metal at 10 inches per hour. You won't get as much out of the severance cutter. It will produce less quality results. The ideal cut is the best choice if you want quality cuts.
Safety
Safety should be your top priority. You should read all safety information provided by the plasma cutter. To protect your eyes, make sure to get good safety glasses. Although the arc may not be as strong as welding, it could still cause damage to your eyes. You can try shades 3 and 5 glasses. Avoid synthetic gloves as they may melt or stick to skin. Always use leather gloves. To protect your skin from the sparks and arc, cover your arms, legs and body with durable cotton material. To prevent injuries from metal falling, you should wear steel protection boots while you are chopping.
Weight
When buying equipment, weight is an important consideration. You don't want your equipment to weigh you down. Inverter technology has made most plasma cutters relatively lightweight. A plasma cutter that has an integrated air compressor might weigh a little more, but it will be much easier to transport as all you need is the plasma cutter.
Consumables
Consumables will cost you an ongoing fee after your plasma cutter is purchased. Consumables include the shield cap, nozzle and shield caps, as well as the swirl ring. Each one has a different life expectancy depending on many variables. However, they will all be damaged when the torch is used to pierce metal or the molten metal returns onto it. Otherwise, the hole must be perfect round. The put depth will affect how the cut is made. Long-lasting consumables are more common for more costly welders. Because of the high quality consumables, Hypertherm machines can be expensive but have low operating costs.
Severance Thickness
To cut metal effectively, the plasma cutter must be able to cut up to a severance thickness. The severance thickness will result in a slow cut and the machine not producing enough heat to make a clean-cut. For regular or best results, it is not recommended to cut metal at the thickness of the severance.
Built-in Air Compressor
You will need to add an air compressor to most plasma cutters before it can be used. Some plasma cutters have an integrated air compressor. They are more costly but offer more convenience as you don't have to bring your own compressor if you go out into the field. It doesn't require you to connect an air compressor or any other equipment. You can just plug the device in and get cutting. They are worth looking into for a little extra cash.
Pilot Arc
Plasma cutters with better cutting features will include a pilotarc. This allows you to make cuts without your torch tip coming in contact with any metal. The pilot arc can be used to cut through rusty and painted surfaces. If you plan to cut rusty, or painted surfaces, you will need to wash the spot where the ground clamp is connected. If you are working on metal that has gaps, such as mesh sheets, it is not necessary to stop or start the torch. The continuous arc will keep the torch lit. A pilot arc is a standard feature for most welders, except those made in China.
Voltage
The plasma cutters can be used with an indoor power supply that is compatible with 110/115/120V input power. They are ideal for home use or beginners, however they have a limited power output. You will need a plasma cutter with a 220V input if you require more power. This is not compatible with generators. You can choose between two power supply options for your plasma cutter: 110V or 220V. These are my favorites because of their versatility.
Duty Cycle
The machine's duty cycle is the time it can continue to operate without cooling down. A 35% duty cycle with a fixed amperage and voltage would mean the plasma cutter could run for approximately 3.5 minutes, instead of 10, without needing to cool down. Lower amperage will result in a longer duty cycle. For deep, long-lasting metal cutting, a longer duty cycle with a greater amperage will be more efficient.
FAQs
1. Is A Cheap Plasma Cutter Worth It?
You should not buy a low-quality plasma cutter. It will not deliver the power, durability and quality you need. A plasma cutter with low prices may be able to cut thinner sheets.
2. How Much Air Pressure Is Needed For A Plasma Cutter?
It is best to buy a compressor with 1.5x the CFM (cubic feet per hour) that the plasma cutter requires. Then, have it delivered at the PSI (pounds/square inch) that the tool needs.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
Plasma cutters can operate between 60 and 120 PSI, depending on their output range.
3. What Is Possible To Cut By Plasma Cutting?
Plasma cutting can be done with all electrically conductive metals, as long as there is an electric current circuit running through the workpiece and clamp.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
An electric current creates an arc, and the heat from the arc melts metal into ionic plasma. Once it passes through an opening, the plasma expands and speeds up. This causes the air pressure to blow away any molten metal plasma and produce a precise and clean cut.
It can be used to cut metals such as copper, aluminum and brass. The machine can also cut electrically-conductive materials.
4. How Do You Set Up A Plasma Cutter?
Plasma cutting works on the principle that complete electric current is used. Therefore, a ground clamp will be required. You should choose a safe surface for your workshop that allows you to move freely around the work area.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
After rechecking that the compressor is working, it's time to turn on the machine. Connect the compressor to the cutter, and observe the constant flow of air pressure.
Place your workpiece on the table, and attach a ground clamp as close as you can to ensure the best result. Turn on the unit using a flicker and press a button marked power or on/off.
5. How Much Faster Is A Plasma Cutter?
Plasma cutting is the best method of cutting metal. A good plasma cutter can cut up to 200 inches of metal per minute.
People are still working to increase the speed. Better speed means better products.
People are still working to increase the speed. Better speed means better products.
6. Can We Cut Wood Or Plastic With A Plasma Cutter?
It is impossible to cut nonconductive materials. Plastic and wood are both electrically resistant materials.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
Prerequisite for the air pressure maintenance and current setting is the metal thickness. To start cutting, bring the nozzle close to the metal.
7. Why Does My Plasma Cutter Cut On An Angle?
Plasma metal cutters can plasma cut at odd angles for a variety of reasons. These include the following: The torch nozzle is worn; there's insufficient power to thearc; you are cutting too fast for your power rating; there's too much gas going to thenozzle; or the plasma cutter is working too slowly.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
It is worth noting, however, that plasma cutters tend to have a slightly "bevel", or angle to cut, of approximately 1-3 degrees. This is due to how the gas jet enters the nozzle. You can decrease this, but it can't be eliminated completely.
8. How Do I Choose A Plasma Cutter?
Consider the cost of the plasma cutter and the inputs. Will they provide enough power to cut through the desired thickness?
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
You should also consider the type of finish you require, as well as whether you prefer a torch with a lead (your project requirements will dictate which lead length you use). Also, you must decide what torch technology you believe will be most effective in achieving the exact cutting you will need as a metal fabricator on the jobsite.
With new information arriving, our editor will usually update the Plasma cutter jegs frequently. Please constantly check our site for the most up-to-date material.
We will try our best to help you with more Plasma cutter jegs. You are supposed to be free to ask for assistance with your problems.
By, Adam Alter
